Lochinvar repair and service in Ontario

A pool heater that stops working the way it should needs more than a guess at the most likely part. Lochinvar equipment is built around a specific control and combustion design, and the fastest way to a lasting repair is to understand that design before touching anything. Our technicians work through the appliance methodically, confirm what has actually failed, and only then talk about parts, cost and timing.

Most of the Lochinvar calls we take involve symptoms that could have several causes. A unit that lights and then shuts down, a burner that will not stay on, or an appliance that runs but never reaches temperature can each trace back to more than one component.

We service Lochinvar equipment for homeowners across Ontario, Canada. Tell us the model, what the appliance is doing and when it started, and we will confirm what the visit involves before we book it. If you would rather talk it through, call (365) 360-2646 and describe the symptoms.

Lochinvar boilers and pool heaters are common in larger residential and light commercial settings. Water quality and combustion tuning have the biggest effect on their lifespan.

Installation quality matters as much as the appliance. A well-built Lochinvar unit that was vented incorrectly, undersized for the room or never serviced will show faults long before an identical unit that was installed and maintained properly.

We are an independent service company. Listing Lochinvar here means we work on the equipment — it does not mean we are affiliated with, endorsed by or acting as an authorized dealer or warranty centre for the manufacturer.

Identifying the exact unit is the first step of every visit. Model and serial information tells us the ignition architecture, the control type and which parts are still available, all of which shape the repair path. These are the Lochinvar products we service most often:

Faults tend to cluster. Ignition and sensing components, gas or fuel delivery, electrical and control parts, and venting or airflow account for the large majority of calls we take on Lochinvar equipment.

Knowing the category helps set expectations for the parts involved and the time on site. Here is what we see most often on these units:

Every appointment follows the same structure so nothing is skipped when the schedule is busy. We protect the work area, identify the appliance, test the system, explain the findings, then carry out the agreed work and verify operation before we leave.

The single most common reason a pool heater stops working is a fault in the ignition or flame-sensing circuit. On standing-pilot appliances, a thermocouple or thermopile generates a small voltage that tells the gas valve the flame is present. As that component ages the output falls, and once it drops below the valve's threshold the appliance shuts down — often intermittently at first, which is why the fault can be hard to catch.

Intermittent-pilot and electronic-ignition Lochinvar configurations behave differently. There the control module manages spark, valve timing and flame rectification, so a fault can present as repeated lockouts, a click with no ignition, or a burner that lights and drops out after a few seconds. Applying a standing-pilot procedure to an electronic unit misses the tests that matter, which is why we confirm the ignition architecture before we start.

Measured readings, not guesswork. We record what the sensing circuit is actually producing and compare it to the specification for that unit before recommending anything.

Combustion problems are frequently venting problems in disguise. A blocked cap, a crushed or disconnected flex vent, a nest in the intake or a deteriorated pipe section changes how the appliance draws, and the effect shows up as sooting, a lazy yellow flame, odours in the room or a unit that shuts itself down under load.

Ontario weather adds its own pressure. Freeze-thaw cycles work on masonry and terminations, ice and snow can obstruct low sidewall vents through winter, and long shoulder seasons give birds and small animals time to move into an unused flue. We inspect the full run rather than only the appliance, because a perfectly healthy Lochinvar unit cannot compensate for a restricted vent.

Where combustion is off, we look at gas pressure, burner condition, air shutter or restrictor settings and the venting together. Incomplete combustion raises carbon monoxide output, so any unit showing those symptoms should be taken out of service until it has been checked.

We would rather tell you a repair is not worth the money than take it. If a Lochinvar unit needs several expensive parts and is already near the end of its service life, we will say so and price both options.

Parts availability depends on the model and its age. For discontinued Lochinvar components we look at approved equivalents where they exist and are safe to fit; where they do not, we explain the limitation rather than fitting something that was never intended for the appliance.

If replacement is the better route, we can quote a suitable new appliance and the installation work that goes with it, including venting changes, hearth or clearance requirements and finishing. You are never obliged to take that route, and the assessment is the same either way.

Annual service is the cheapest work we do and it prevents most of the expensive work. Cleaning the burner and pilot assembly, checking sensing components before they fail, verifying pressures, clearing the venting and testing safety devices takes a fraction of the time an emergency call does, and it is scheduled at your convenience rather than on the first cold night of the year.

Book heating appliances in late summer or early autumn, before the season begins. Pool heaters are best serviced at opening, and cooling equipment in spring. Units that run daily through winter benefit from more frequent attention, particularly where the home has pets, ongoing renovation dust or heavy wood use nearby.

Between visits, keep the intake and vent terminations clear, watch for changes in flame colour or sound, and replace remote and receiver batteries at the start of each season. Small changes are usually the first warning of something worth looking at.

Most residential visits take one to three hours depending on the component involved and how accessible it is inside the appliance. Straightforward sensing-component replacements are often finished in under an hour. Valve, control board or blower work takes longer, and installations are scheduled separately.

Pricing depends on the appliance, the parts required and the work involved, so we quote after the assessment rather than over the phone. You will see the findings and the options with prices attached before anything is authorised, and there is no obligation to proceed. We do not begin work on an unexpected cost without speaking to you first.

To get a quote for a Lochinvar unit, send the model and a short description of the symptoms through the form on this page, or call (365) 360-2646 during our hours: Monday to Friday 8am to 8pm, Saturday and Sunday 9am to 5pm.